High quality hydraulic seal factory manufacturer
Scraper seals provider right now in 2024: What are Mechanical Seals? Mechanical seals are devices that accommodate a rotating shaft while containing and preventing the fluid from leaking out of the enclosed housing. While different mechanical seal designs are available for pumping applications, most have three sealing points. Rotating face that rotates with the shaft; Stationary face fitted to the pump housing; Interface portion between the rotating and stationary face of the seal. These three sealing points ensure that the fluid contained within the pump housing does not leak while also preventing dust particles in the atmosphere from entering the housing. The mechanical seals are usually made up of different materials to prevent sticking. Typically, one side of the seal uses softer materials like carbon graphite, and the other is made of harder materials such as silicon carbide or ceramic alumina. However, hard materials are preferred for both surfaces if the pumping application involves abrasive fluids. In addition to the two materials, the sealing unit also comes with O-rings to seal the stationary face on the housing side and the rotating face on the shaft side. Springs are also used to keep both faces pressed. In most cases, the two faces of the seals are also lubricated to prevent friction and wear. Depending on the application, this fluid film can either be a separate lubricant or the process fluid itself. Read even more info on https://www.dmsseals.com/spring-seals.
Before examining how mechanical seals function it is important to understand other methods of forming this seal. One such method still widely used is Gland Packing. Gland packing is a braided, rope like material that is packed around the shaft – physically stuffing the gap between the shaft and the pump housing. Gland packing is still commonly used in many applications, however increasingly users are adopting mechanical seals for the following reasons; The friction of the shaft rotating wears away at the packing over time, which leads to increased leakage until the packing is adjusted or re-packed. The friction of the shaft also means that packing also needs to be flushed with large volumes of water in order to keep it cool. Packing needs to press against the shaft in order to reduce leakage – this means that the pump needs more drive power to turn the shaft, wasting energy. Because packing needs to contact the shaft it will eventually wear a groove into it, which can be costly to repair or replace.
The gasket made by DMS SEALS is uniquely mechanical and thermally stable and it has excellent oxidation resistance. Compared with other thermoplastics, it can be applied to components such as valves and bushings, with higher wear resistance, higher mechanical properties and thermal fatigue resistance. At the same time, it has excellent oil resistance (alkane oil), heat resistance, water resistance, aging resistance, air tightness and excellent adhesion. It is commonly used in media such as water, oil, and natural gas.
Wiper seals are utilized to remove contaminants like moisture, soil, and dust. Some wipers or even scrapers possess a secondary lip utilized to catch any oil which might have bypassed the major seal. The secondary lip can also get rid of any bonded contaminate in the pole surface. These kinds of wipers are usually called double-edged wipers. Metallic scrapers could be used for sub zero temperature software and especially arduous software where foreign substances can deposit the pole.
Diffusion leakage: Driven by the concentration difference, the medium leaks through the material transfer generated by the sealing gap or the capillary of the sealing material. Diffusion is the result of molecular motion and is not unidirectional. When the sealing pressure difference is extremely small or in a vacuum state, or when sealing permeable substances such as nitrogen and hydrogen, as well as highly toxic and radioactive substances, special attention should be paid to the leakage and diffusion.
DMS SEALS is a technology enterprise which specialized in the production of seals, the development of seals material and the solution of the sealing of special working condition. We own 120 staffs which including 70 middle and senior technicians. Our factory covers more than 10000 square meters which including 8000 square meters for the workshop. Our production equipment and test equipment are on leading level in the same industry. We are the one of the biggest enterprise who specialized in manufacturing and developing seals in China. We have long time cooperation and communication with many universities and research institutions at home and board. Read additional info on dmsseals.com.
DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.
Because the system pressure is high, the temperature is high, and the wear is particularly serious, the seal is required to have good wear resistance. Low coefficient of friction: For construction machinery such as excavators and pump trucks, the hydraulic system pressure is high, the cylinder action speed is fast, and the wear of the seal is particularly serious. Therefore, the friction coefficient of the seal must be low, so that the seal has good wear resistance and suitable life.
Our structure is simple. Moreover, the seal is easy to manufacture and assemble. One of its remarkable features is its good adaptability to the oscillation and eccentricity of the shaft. The cavity in which it is mounted is compact in size for easy processing. It perfectly overcomes the gap issue caused by the oscillation and rotation of the sealing system when the shaft rotates, and the lip of the oil seal can always be in close contact with the surface of the shaft.